Loading...
HomeMy WebLinkAbout2017-06-12 2122 E HIGHLANDS STCity of Bremerton Department of Community Development 345 - 6th Street, Ste. 600, Bremerton WA 98337 (360) 473-5275 Fax: (360) 473-5278 ASSESSOR NUMBER: 3934-000-005-0000 ZONING: Name APPLICANT: AIR MANAGEMENT SOLUTIONS OWNER: KRIEGER KEVIN CONTRACTOR: AIR MANAGEMENT SOLUTIONS LENDER: SUBMITTED: 06/12/2017 PERMIT NUMBER DATE ISSUED BB17 00459 06/12/2017 SITE ADDRESS: 2122 E HIGHLANDS ST Phone Address 360-479-6500 5822 WEST WERNER RD BREMERTON, WA 98312 6491 TRACYTON BLVD BREMERTON, WA 98311 360479-6500 5822 WEST WERNER RD BREMERTON, WA 98312 APPROVED: 06/12/2017 EXPIRATION: 12/09/2017 VALUATION: MechanicaUPlumbing SFR -INSTALL GAS PIPING &FURNACE SFR -INSTALL GAS PIPING &FURNACE Technology Fee $2.49 Mechanical Fixture Fee $49.80 Building Code Edition: Occupancy Group: TOTAL FEES: $52.29 Type of Construction: Flood Zone: Setbacks: Sanitation Method: Number of Bedrooms: Access Code D7WXK-6TE79 YHLZK-3SP80 D7WXK-6TE79 STATUS: ISSUED Inspection Requests: FIRE: Fire Inspections (360) 473-5386 DCD: Building Inspections: (360) 473-5870 HEALTH: Kitsap County Health District (360) 337-5285 L&I: Department of Labor and Industries (360) 415=4000 PW&U: Public Works - Engineering (360) 473=5270 This permit shall become null and void if the described work authorized by this permit has not commenced within 180 days from the date of issuance, or if the work is suspended or abandoned at any time after the work is commenced for a period of 180 days. It is the responsibility of the permit holder to see that the required inspections are made. Failure to obtain required inspections may result in stoppage of the work until such time that the permit holder can susbstantiate to the City of Bremerton that the concealed work meets or exceeds code requirements. Any demolition, testing, or financial burden shall be borne directly by the permit holder. Failure to substantiate code requirements will indemnify the City against any and all responsibility or liability connected with the construction. I hereby certify that I have read and examined this permit and know the same to be true and correct. All provisions of laws and ordinances governing this type of work will be complied with whether specified herein or not. The granting of a permit does not presume to give authority to violate or cancel provisions of any State or local law regulating construction or the performance of the construction. If listing the owner as general contractor, I certify that I am exempt from the requirements of the State Contractor's Registration Law under Section 3, Chapter 126, Laws of 1967. All revisions to an approved plan require DCD review and approval prior to performing work. All building and tenant occupancy permits are required to pass final inspection prior to permit expiration and obtain a certificate of occupancy prior to use or occupancy. I have read, and agree to abide by the conditions is permit ' cl di gall conditions of zoning, building codes, and State and Federal laws. SIGNATURE OF OWNER OR AGENT: � - ✓ PRINTED NAME: _ ` DATE: CONDITIONS Printed by :Wood, Tracey on: 06/12/2017 10:36 AM Page 1 of 4 6 City of Bremerton Department of Community Development 345 - 6th Street, Ste. 600, Bremerton WA 98337 (360) 473-5275 Fax: (360) 473-5278 ASSESSOR NUMBER: 3934-000-005-0000 ZONING: Name APPLICANT: AHt MANAGEMENT SOLUTIONS OWNER: KRIEGER KEVIN CONTRACTOR: AIIt MANAGEMENT SOLUTIONS LENDER: SUBMITTED: 06/12/2017 PERMIT NUMBER: DATE ISSUED Phone Address 360-4794500 5822 WEST WERNER RD BREMERTON, WA 98312 6491 TRACYTON BLVD BREMERTON, WA 98311 360479=6500 5822 WEST WERNER RD BREMERTON, WA 98312 BB17 00459 06/12/2017 SITE ADDRESS: 2122 E HIGHLANDS ST APPROVED: 06/12/2017 EXPII2ATION: 12/09/2017 Access Code D7WXK-6TE79 YHLZK-3SP80 D7WXK-6TE79 STATUS: ISSUED By applying for this permit, the applicant has granted to the City of Bremerton the right to enter the above -described location at reasonable times to inspect the proposed, in -progress or completed work performed under this permit to ensure compliance with the permit conditions and other applicable laws and regulations. Should such entry be refused, all authorizations and approvals contained in this permit shall be immediately suspended and any work performed under the permit shall immediately cease until authorized in writing by the City of Bremerton. Work performed in violation of this condition shall be considered to have been performed without the approval of the City of Bremerton. The City of Bremerton's approval of this application pertains only to the City's regulatory jurisdiction, and thus compliance with City regulations does not necessarily ensure compliance with federal or state laws. 10. (DCD-Ol) ASBESTOS AND LEAD -BASED PAINT: ASBESTOS: Prior to performing any renovation or demolition work, Puget Sound Clean Air Agency and Washington Department of Labor and Industries (L&I) regulations require an asbestos survey be performed to determine whether there are asbestos -containing materials in the work area or structure. 1 The asbestos survey must be conducted by and EPA -certified (AHERA) building inspector (except renovation or owner -occupied single family residences).For more information, please contact Clean Air Agency through their web site at www.pseleanair.org or by phone at 800-552-3565 or 206-343-8800. The L&I web site can be found at www.Ini.wa.gov/TradesLicensing/LicensingReq/Asbestos/default.asp. LEAD -BASED PAINT: A contractor or person receiving compensation who is performing renovation, repairs or painting on a residential building or a child -occupied facility built before 1978, must be trained and certified by an accredited training provider, and registered as a Renovator by the Washington State Department of Commerce- Lead -Based Paint Program. For further information please contact: The Department of Commerce website at: www.commerce.wa.gov/lead, or call: (360) 586-LEAD (5323). CONTRACTOR: A contractor's registration issued by Washington State Dept. of Labor & Industries is required for anyone who contracts or submits bids for construction work, including new construction, alterations, repairs, or anyone who consults or superintends, improves, demolishes, develops residential property for sale, or "flips" houses. Contact L & I at (360)415- 4000 for information. 0. (DCD-02) DCD: Validity of permit. The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, any violation of any of the provisions of the Washington State Building code or of any other ordinance of the City of Bremerton. Permits presuming to give authority to violate or cancel the provisions of the Washington State Building code or other ordinances of the City of Bremerton shalt not be valid. The issuance of a permit based on construction documents and other data shall not prevent the building official from requiring the correction of errors in the construction documents and other data. The building official is also authorized to prevent occupancy or use of a structure where in violation of the Washington State Building code or of any other ordinances of the City of Bremerton. p 10. (DCD40) A separate electrical permit issued through Labor & Industries (L&I) is required for any new, modified, repair, replacement, service, maintenance, or temporary installations. Electrical work is inspected by L&I prior to cover and the framing inspection, Contact L&I at 360415-4000 or www.Ini.wa.gov. (RCW 19.28) 11. (DCD-47) DCD: Reinspection Fee: All approved plans, the printed building permit, and the permit inspection placard, are required to be on -site for inspection purposes, and work to be inspected shall be complete and ready for inspection. If an inspection is called for and plans are not available on site, or the work is not ready for inspection, approval will not be granted. In addition, a re - inspection fee will be charged and must be collected by the Department of Community Development prior to any further inspections being performed or approvals granted. 0A 12. (DCD-08) Plumbing work shall be performed by a Level Ol Journeyman Plumber licensed in the state of Washington. i Residential plumbing work may be performed by a Level Ol or :Level 02 Journeyman Plumber licensed in the state of Washington. Single family residential plumbing work may be performed by the owner. 12. (DCD-50) Final Inspection Required: All building permits shall have a final inspection performed and approved by the City of Bremerton Department of Community Development prior to permit expiration. The failure to request a final inspection or failure to obtain final approval prior to expiration may require a reactivation fee, or a new permit application if more than a year has passed with no activity. The permit expires 180 days past the date of inactivity. Required inspections: Any work required to be inspected and that is covered before such inspection may be required to be uncovered so that the inspection may be performed. Examples of inspections to be performed before covering are mechanical rough -in, plumbing rough -in, gas piping, framing, and sheetrock nailing. Printed by :Wood, Tracey on: 06/12/2017 10:36 AM Page 2 of 4 City of Bremerton Department of Community Development 345 - 6th Street, Ste. 600, Bremerton WA 98337 (360) 473-5275 Fax: (360) 473-5278 ASSESSOR NUMBER: 3934-000-005-0000 ZONING: Name APPLICANT: AHt MANAGEMENT SOLUTIONS OWNER: KRIEGER KEVIN CONTRACTOR: AIR MANAGEMENT SOLUTIONS LENDER: SUBMITTED: 06/12/2017 Phone Address PERMIT NUMBER: DATE ISSUED: 360-479-6500 5822 WEST WERNER RD BREMERTON, WA 98312 6491 TRACYTON BLVD BREMERTON, WA 98311 360-479-6500 5822 WEST WERNER RD BREMERTON, WA 98312 BB17 00459 06/12/2017 SITE ADDRESS: 2122E HIGHLANDS ST APPROVED: 06/12/2017 EXPIRATION: 12/09/2017 Access Code D7WXK-6TE79 YHLZK-3SP80 D7WXK-6TE79 STATUS: ISSUED 13. (DCD-52) DCD: Gas Piping: Fuel or gas piping shall be inspected after the installation of fueUgas piping is complete, and before the attachment of fixtures, appliances, or shut-off valves. At the time of inspection the test pressure shall be no less than 10 psi held for no less than 15 minutes. Appliances to be attached to the fuel/gas piping system shall not be used until the final inspection has been performed and approved by a Building Inspector. 14. (DCD-56) Combustion Air: In buildings of unusually tight construction, or within a garage, all fuel -burning appliances, other than cooking appliances and domestic clothes dryers, shall obtain combustion air from outside in accordance with the International Mechanical Code, International Fuel Gas Code and/or the International Residential Code. 15. (DCD-FUEL COMBUSTION AIR: IRC Section M1701.1. Solid-fuel-buming appliances shall be provided with combustion air in APPLIANCES) accordance with the appliance manufacturer's installation instructions. Oil -fired appliances shall be provided with combustion air in accordance with NFPA 31. The requirements for combustion and dilution air for gas -fired appliances shall be in accordance with Chapter 24. Fireplaces shall comply with Section 1001. APPLIANCE LOCATIONS: IRC Section G2406.2. Fuel burning appliances shall not be installed in a sleeping room, bathroom, toilet room, or closet. Exception: direct vent appliances (see IRC Section G2406.2 for additional exceptions). PROTECTION OF APPLIANCES: IRC Section M1307.3. Appliances located in a garage or carport or any other location subject to vehicle damage shall be protected by approved barriers. Appliances having an ignition source shall be elevated so that the source of ignition is at least 18" above the floor in garages and in any room that opens to the garage. Appliances designed to be fixed in position shall be fastened or anchored in an approved method. CARBON MONOXIDE ALARMS: IRC Section 315. An approved carbon monoxide alarm listed with UL 2034 shall be installed outside of each separate sleeping area in the immediate vicinity of the bedroom. In a building where a tenancy exists, the tenant shall maintain the CO alarm as specified by the manufacturer including replacement of the batteries. MANUFACTURER'S SPECS: IRC M1307.1. The manufacturer's operating and installation instructions shall remain attached to the appliance until final inspection 16. (DCD-14) DCD: Approved Plans, Engineering, Site Plan, Permit, and Conditions shall remain on site and be available for inspection. Any changes to plans shall be approved before construction is performed. Architect or engineer of record shall approve the change before submitting a revision. A revision is subject to a revision fee and additional fees for plan review and inspections. 17. (DCD-CO DET. CARBON MONOXIDE ALARMS: IRC Section 315.1. An approved carbon monoxide alarm (iJI, 2034) shall be installed (EXIST)) outside of each separate sleeping area in the immediate vicinity of the bedroom in dwelling units and on each level of the dwelling in accordance with the manufacturer's recommendations. In a building where a tenancy exists, the tenant shall maintain the CO alarm as specified by the manufacturer including replacement of the batteries. 18. (DCD-CO DET. (NEW)) Carbon Monoxide Alarms. For new construction, an approved carbon monoxide alarm listed in compliance with UL 2034 shall be installed outside of each separate sleeping area in the immediate vicinity of the bedroom in dwelling units and on each level of the dwelling. In a building where a tenancy exists, the tenant shall maintain the CO alarm as specified by the manufacturer including replacement of the batteries. MINIMUM INSPECTIONS REQUIRED To request an inspection, please call (360) 473-5870 and be sure to provide your permit number, name on permit, site address, contact phone number, and inspection type. To register for on-line inspection access, visit the City's website at www.ci.bremerton.wa.us. Inspection GAS PIPING MECHANICAL PLUMBING GROUND PLUMBING - ROUGH FINAL - BUILDING Description Gas Piping Pressure Test Mechanical Rough -In Plumbing Groundwork Plumbing Rough -In Final Inspection - Building Printed by :Wood, Tracey on: 06/12/2017 10:36 AM Page 3 of 4 City of Bremerton Department of Community Development PERMIT NUMBER: DATE ISSUED: BB17 00459 06/12/2017 345 - 6th Street, Ste. 600, Bremerton WA 98337 SITE ADDRESS: 2122 E HIGHLANDS ST (360)473-5275 Fax: (360) 473-5278 ASSESSOR NUMBER: 3934400-0054000 ZONING$ Name Phone Address Access Code APPLICANT: AIR MANAGEMENT SOLUTIONS 360=479-6500 5822 WEST WERNER RD D7WXK-6TE79 BREMERTON, WA 98312 OWNER: KRIEGER KEVIN 6491 TRACYTON BLVD YHLZK-3SP80 BREMERTON, WA 98311 CONTRACTOR: AIR MANAGEMENT SOLUTIONS 360479-6500 5822 WEST WERNER RD D7WXK-6TE79 BREMERTON, WA 98312 LENDER: SUBMITTED: 06/12/2017 APPROVED: 06/12/2017 EXPIRATION: 12/09/2017 STATUS: ISSUED Printed by :Wood, Tracey on: 06/12/2017 10:36 AM Page 4 of 4 I �kre1 Fv._.J 7a r d 2017 PERMIT CENTER '' f-t Bra,/ . r,.erto,�, �Cb RESIDENTIAL MECHANICAL /PLUMBING Dept. of Community Development *345 — 6th Street, Suite 600*Bremerton*WA*moot I of 3 Type of Fuel: ❑ Electric J as ❑Oil ❑ Propane Site Address: 212Z '1::�O CONTRACTOR:��� Q�p� eMinWNER: eV lVl I t12 Address: 582.Z Y�IeY it d Address: �}q I �(� ►� t City, State, Zip: 1651 Z City, State, Zi ✓ m vt 1N k q I License #: 59 5 . Phone # Tax ID/Parcel #: 93 • WO. DOS • 00() 0 Contact Phone #: 3 (o0 1 cl • (OS0 b Bremerton Business License: 25I1 IftA QTY TYPE OF EQUIPMENT QTY TYPE OF EQUIPMENT AIR CONDITIONER / EVAP COOLER BUILDING SEWER BOILER < = 100K BTU CLOTHES WASHER BOILER > 100K <= 500K DISHWASHER CLOTHES DRYER WITH EXHAUST DRAIN PIPE CHANGE COOK STOVE FLOOR DRAIN / TRENCH DRAIN FAN / BATH OR EXHAUST HOSE BIBB FIREPLACE GAS OR GAS LOG INSERT LAWN SPRINKLER W/ BACKFLOW DEV FIREPLACE WOOD OR WOODSTOVE MISC PLUMBING FURNACE ELECTRIC / HEAT PUMP SINK (LAV, KITCHEN, MOP OR BAR) FURNACE LP GAS / DUCTING SUMP PUMP FURNACE NATURAL GAS / DUCTING TUB AND/OR SHOWER UNIT FURNACE OIL TOILET / BIDET 1 GASPIPE SYSTEM WATER HEATER ELECTRIC LP TANK < 2000 GALLONS WATER PIPE CHANGE MISC MECHANICAL EQUIPMENT RANGE HOOD WATER HEATER GAS AND VENT MISC MECHANICAL Applicant's Signature I IN lia Print Name Date Rev. June 2016 Ameristar 7/8" DIA. HOLES ELECTRICAL CONNECTION 3-13/16" 1-1/2" DIA. HOLE �3/8" GAS CONNECTION 2-1/8" •I I • orizomai duced Draft Single age Gas Furnace 4" DIAMETER FLUE CONNECT (r3 7/8"HOLE WITH PLUG ELECTRICAL CONNECTION (ALTERNATE) �iJ 1-S/8"HOLE WITH PLUG (2) FURNACE AIRFLOW (CFM) VS. EXTERNAL STATIC PRESSURE (IN. MODEL SPEED TAP 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 4-HIGH - Black 1426 1389 1345 1298 1236 1 171 1099 1020 934 3-MED - HIGH - Blue 1243 1225 1197 1160 1113 1057 991 916 831 M801 P060AU36AA 2-MED - LOW - Yellow 1042 1039 1027 1005 973 931 879 817 745 1-LOW - Red 900 903 895 877 848 809 760 700 629 CFM VS. TEMPERATURE RISE MODEL CFM (CUBIC FEET PER MINUTE) 500 1 600 1 700 1 800 1 900 10001100 120013001400 150016001700 M801PO60AU36AA 56 49 44 40 37 34 1 32 © 2015 Ingersoll Rand ■ PRODUCT SPECIFICATIONS r' MODEL M801P060AU36AA TYPE U flow/Horizontal RATINGS C Input BTUH O 60 000 Capacity BTUH (ICS) 47,000 Temp. rise (Min. -Max.) 'F. 30 - 60 BLOWER DRIVE Direct Diameter - Width (In.) 10 x 6" No, Used 1 Speeds (No.) 4 CFM vs. in. w.g. See Fan Performance Table Motor HP 1/3 R.P.M. 1075 Volts/Ph/Hz 115/V60 COMBUSTION FAN -Type Centrifugal Drive - No. Speeds Direct - 1 Motor HP - RPM 1/50 - 3180 Volts/Ph/Hz 115/1 /60 FLA 1.09 FILTER — Furnished? No Type Recommended High Velocity Hi Vel. (No.-Size-Thk.) 1 -16x25 -1 in. VENT — Size (in.) 4 Round HEAT EXCHANGER Type - Fired Alum. Steel - Unfired Gauge (Fired) 20 ORIFICES — Main Nat. Gas. Oty. — Drill Size 3 — 45 L.P. Gas City, — Drill Size 3 — 56 GAS VALVE Redundant - Sinale Stacie PILOT SAFETY DEVICE BURNERS —Type Multiport Inshot Number 3 POWER CONIC—V/Ph/Hz '�4 115/1/60 Ampacity (In Amps) 9,0 Max. Overcurrent Protection (Amps) 15 HxWxD Crated Shipping (Lbs.)/Net (Lbs.) 127 / 118 Central Furnace heating designs are certified to ANSI Z21.47 /CSA 2.3. ..� For U.S. applications.. above input ratings (BTUH) are up to 2.000 feet. Berate 4 %per 1,000 feet for elevations above 2,000 feet above sea level. For Canadian applications, above input ratings (BTUH) are up to 4,500 feet, derate 4% per 1,000 feet for elevations above 4,500 feet above sea level. Based on U.S. government standard tests. The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes. NATURAL GAS MODELS -Central Heat- ing furnace designs are certified to ANSI Z21.47 / CSA 2.3 for both natural and L.P. gas. Limit setting and rating data were established and approved under standard rating conditions using American National Standards Institute standards. SAFE OPERATION The Integrated System Control has solid state devices, which continuously monitor for presence of flame, when the system is in the heat- ing mode of operation. Slow opening, dual solenoid combination gas valve and regulator provide extra safety and quieter operation. QUICK HEATING— Durable, cycle tested, heavy gauge aluminized steel heat exchanger quickly transfers heat to provide warm conditioned air to the struc- ture. Low energy power vent blower, to increase efficiency and provide discharge of gas fumes to the outside, allows com- mon venting with hot water heater. Since the manufacturer has a policy of continuous product and product data improvement. it reserves the right to change specifications and design without notice. Technical Literature -Printed in U.S.A. Ingersoll Rand 11819 N. PennsylvaniaStreet Carmel, IN 46032 BURNERS -Multiport Inshot burners will give years of quiet and efficient service. All models can be converted to L.P. gas without changing burners. INTEGRATED SYSTEM CONTROL - Exclusively designed operational program provides total control of furnace limit sensors, blowers, gas valve, flame control and includes self diagnostics for ease of service. AIR DELIVERY -The multispeed, direct drive blower motor, with sufficient air- flow range for most heating and cooling requirements, will switch from heating to cooling speeds on demand from room thermostat. The blower door safety switch will prevent or terminate furnace operation when the blower door is removed. (Fan relay and 35VA control transformer is standard). E1V �S <,s, u Intertek STYLING -Heavy gauge steel and "wrap -around" cabinet construction is used in the cabinet with baked -on enamel finish for strength and beauty. The heat exchanger section of the cabinet is com- pletely lined with foil faced fiberglass in- sulation. This results in quiet and efficient operation due to the excellent acoustical and insulating qualities of fiberglass. FEATURES AND GENERAL OPERA- TION -The High Efficiency Gas Furnaces employs a Silicon Nitride Hot Surface Ignition system, which eliminates the waste of a constant burning pilot. The integrated system control lights the main burners upon a demand for heat from the room thermostat. Complete front service access. a. Low energy power venter b. Vent proving pressure switch. Library Ameristar Product Section Furnaces Product Furnace Model M801 Literature Type Submittal Sequence - Date 05/15 Flle No. M801P060AU36-SUB-1A Supersedes M801 P060AU36-SUB-1 i 0